|
HX-S PearlNickel Process
1. Characteristics TEL:+8613243796333
1).The sense of sand thickness with exquisite, soft and strong metallic finishing; non-easy contaminate by finger mark. Keeping consistent and even in the plating, the color is matte white with slight lustre.
2).This process is applied to all upscale hardware and plastic（Bathware, Furniture hardware, Computer, Electron device and etc.）
3) This Pearl Nickel can be instead of HX-SC1 fine-white sand agent or HX-SC2 semi-white sand agent per the requirements of products.
2. Plating ingredients and operation conditions:
|
Ingredients and Conditions
|
Operation Scopes
|
Standards
|
|
Nickel sulfate
|
420-500g/L
|
450g/L
|
|
Nickel chloride
|
35-50g/L
|
45g/L
|
|
Boric acid
|
35-45g/L
|
42g/L
|
|
HX-SA Make Up Agent
|
5-18ml/L
|
15ml/L
|
|
HX-SB Adjuvant
|
6-12ml/L
|
8ml/L
|
|
HX-SC Sand Agent
|
0.6-1.8ml/L
|
0.5ml/L
|
|
Timing
|
1-5 Minutes
|
4 Minutes
|
|
Current density
|
3-8 Amps/ square decimeter
|
4 Amps/ square decimeter
|
|
Temperature
|
52℃-60℃
|
58℃
|
|
PH
|
4.0-4.8
|
4.5
|
|
Stirring method
|
Mechanical stirring, moving repeatedly or rotating
|
|
Filtration
|
No request filtration for producing 10-15 days, the plating solution is requested to filter after treatment of Carbon Activated per producing 15-30 days.
|
|
Flow of Plating Solution
|
Non-stop circulation by using magnetic pump,
No need to circulate and keep the heat preservation with no production
|
3. The ingredients for plating solution ofPearlNickel
1). Pour 60% water into the clean barrel and heat it to60℃.
2). Add all necessary Nickel sulfate, Nickel chloride and Boric acid; mix them to dissolve completely.
3). Add 2-5g/L of the Carbon Activated and stir with hours.
4). Filter the plating solution to clean plating tank and under-current electrolyze 6-8 hours with 1V voltage.
5). Adjust the PH value within the operation scopes and add the requested water.
6). Add the Pearl Nickel HX-SA and HX-SB while stirring. (Add HX-SC after dilute to 10 times of water and stir gently, motionless electrolyte 10-20 minutes for the plating solution after stirring it with10 minutes, then start to plating).
7). Strong recommend using the air pump for circulation in production.
4. The management and maintenance for plating solution ofPearlNickel
Regularly analyse the elementary ingredients of plating solution and adjust the volumes within operation scopes. Conduct the Hull Cell Testing before daily operation to adjust the additive volume under the optimum condition, or refer to below additive volume for adjustment.
1.) Additive consumptions:
Name of the Additive Consumption / 1000 Amps / H
HX-SA Make Up Agent 120- 160 ml.
(Refill more if get shining and foggy in high section)
HX-SB Adjuvant 50-100 ml.
(Get glossy by added too much coating)
HX-SC Sand Agent 100-150 ml.
(Add it for sandy thinning or sandy slowly)
2). Refer to the standard make-up volume for the new barrel.
3). Refill volume for running 8 hours without filter the plating solution.
HX-SA Make Up Agent Make-up volume 10-20% (1 ml.)
HX-SB Adjuvant Make-up volume 5-10% (0.6 ml.)
HX-SC Sand Agent Make-up volume 20-50% (0.4 ml.)
4). Refill make-up volume after wick filter the plating solution.
HX-SA Make Up Agent Make-up Volume 0-10%（0.5ml.）
HX-SB Adjuvant Make-up Volume 0-5%（0.5 ml.）
HX-SC Sand Agent Make-up Volume 100%（0.8 ml.）
5). Refill volume after filter by wick and toner.
HX-SA Make Up Agent Make-up Volume10-30%（2 ml.）
HX-SB Adjuvant Make-up Volume 5-15%（0.5 ml.）
HX-SC Sand Agent Make-up Volume 100%（0.8 ml.）
6). Refill additive volume after the major treatment of the toner.
HX-SA Make Up Agent Make-up Volume 30-60%（6 ml.）
HX-SB Adjuvant Make-up Volume 20-40%（3 ml.）
HX-SC Sand Agent Make-up Volume 100%（0.8 ml.）
|
产品中心 << 